Building & construction

Applications

Vacupor® Vacuum Insulation Panels for facade elements
Today modern facade constructions are widely dominated by sandwich elements. As surface layers high-quality materials such as aluminium and glass sheets can be used. In order to reach this high-quality standard as well for the core insulation material, high performance insulation is required.

Terrace and floor insulation with Vacupor® VIPs / vacuum insulation panels
Barrier-free terrace access at low cost - Vacupor® vacuum insulation panels allow offset-free implementation of terrace accesses. With Vacupor®, terrace and balcony insulation can be achieved with a slim and elegant design. We deliver high-performance insulation ready for the construction site, which is specially designed for terrace installation.

Vacupor® Vacuum Insulation Panels for flat roof insulation
Flat roofs can be found on industrial buildings and also on renovated old buildings of various designs. Here, too, construction height and energy efficiency play the decisive role in the choice of insulation material.

Wall insulations with Vacupor® vacuum insulation panels
Bring on the 2009 energy conservation requirements (Germany) – enhanced requirements are easily met by Vacupor® vacuum insulation panels. Vacupor® VIPs offer a slimness of construction previously unimagined and thus give ample free space for design. Through consistent use of Vacupor® vacuum insulation panels, valuable living space is gained. That leads to an increase in the usable area and a more favorable ratio of floor space / usable area.

DAD – outside insulation, roof or ceiling, under coverage
DAD – outside insulation of roof or ceiling, protected against weathering, insulation under coverage. Whether in industrial or residential construction, for flat or steep roofs, Vacupor® stands out as a superb high-performance insulation material. Especially when renovating, Vacupor® will be a preferred choice among insulation materials because no conventional insulation material offers such good insulation characteristics with a drastic reduction of construction height.

DAA – outside insulation, roof or ceiling, under seal
DAA – outside insulation of roof or ceiling, protected against weathering, insulation under seal. With flat and steep roofs, Vacupor® stands out as a superb high-performance insulation material. Especially when renovating, Vacupor® will be a preferred choice among insulation materials because no conventional insulation material offers such good insulation characteristics with a drastic reduction of construction height.

DZ – common rafter insulation
DZ – common rafter insulation, ventilated roof, not walkable, but accessible uppermost ceilings. With steep roofs, Vacupor® stands out as a superb high-performance insulation material. If the insulation performance is to be noticeably improved when renovating a roof and the height of the rafters is to remain unchanged, this can be easily achieved with Vacupor®.

DI – inside insulation of the ceiling or roof
DI – inside insulation of the ceiling (on the underside) or the roof, insulation under the rafters / supporting structure, suspended ceiling, etc. With Vacupor® vacuum insulation panels, you have an ideal solution – if, e.g., insulation with conventional insulation materials is not possible due to limited space heights, planning errors, etc.

DEO – inside insulation of the ceiling or ground slab
DEO – inside insulation of the ceiling or ground slab (on the top) under screed without noise protection requirements. This is where Vacupor® vacuum insulation panels are an ideal solution – if, e.g., insulation with conventional insulation materials is not possible due to limited space heights, planning errors, etc., or avoidance of steps/offsets is required.

WAB – outside wall insulation behind sheathing
WAB – outside wall insulation behind sheathing. Porextherm Vacupor® vacuum insulation panels (VIPs) meet the requirements of the German energy conservation provision EnEV without difficulty and without drastically increasing the insulation thickness. On the contrary, Vacupor® VIPs allow a slimness of construction previously unimagined and thus offer ample free space for design.

WAA – outside wall insulation behind seal
WAA – outside wall insulation behind seal Since extension of the building inspection approval (Germany), Vacupor® VIPs can also be profitably used as an innovative wall insulation system, both in new buildings and when renovating old buildings.

WH – insulation of wood frame and wood panel construction
WH – insulation of wood frame and wood panel construction. Vacupor® VIPs allow a slimness of construction previously unimagined and thus offer more free space for design. Sophisticated designs thus become possible. Slim and high-temperature insulated wall systems in wood frame or wood panel construction can thus be easily implemented.

WTR – insulation of space separation walls
WTR – insulation of space separation walls. Vacupor® VIPs allow a slimness of construction previously unimagined and thus offer more free space for design, in the inside area as well. Sophisticated wall or separation systems thus become possible. A slim and highly efficient separation wall system can thus be easily implemented.

WI – inside wall insulation
WI – inside wall insulation. Insulation with Vacupor® VIPs allows a slimness of construction previously unimagined. The free space for design is thus also expanded in the inside. Sophisticated inside wall insulation thus becomes possible. The usable space lost is thus reduced to a minimum and insulation becomes possible where it cannot be insulated from the outside.

Vacupor® vacuum insulation panels in roller shutter casings and lamellar-blind-boxes
Due to the application of Porextherm Vacupor® VIPs (vacuum insulation panels) in roller shutter casings and lamellar-blind-boxes, thermal bridges can be avoided and the increased requirements of the EnEV can be kept.